Project

General

Profile

mike5000's activity

From 2017-04-20 to 2017-05-19

2017-05-19

09:28 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
JohnO wrote:
> When you say you have tried both I suspect you mean that you have tried the 5v and the 3v3 Sparkfun b...
mike5000
09:25 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
JohnO wrote:
> The pinout is visible here:
> https://cdn.shopify.com/s/files/1/0032/7122/products/usb-bub2_large.jp...
mike5000

2017-05-18

21:12 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
I assume the Sparkfun FTDI board is pin compatible with the Jeenode? I recall something about an auto reset function ... mike5000
20:58 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
Tried both. What is the correct programmer setting in the Arduino IDE when I use FTDI? mike5000
20:19 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
Tried both the 5V FTDI and the 3,3V FTDI boards from Sparkfun now. The 5V version outputs 5V on IO pins as well. The ... mike5000
17:51 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
Thanx. I assume the diode is shorted on new boards (no diode in my kit) mike5000
17:37 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
Ok thanks. Will look into that later.
If I had a schematic I would have seen how the regulator is connected.
W...
mike5000
16:43 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
Sorry for being unclear.
I have two Sparkfun FTDIbreakout boards.
One is marked 3.3 V(the one I used)
One is ...
mike5000
16:32 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
So a 5.5v version of the ftdi must be used? mike5000
16:16 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
What "programmer" is the right one? I have a 3,3 FTDI interface from Sparkfun and hardly a programmer connected. mike5000
16:13 JeeLabs Café Support: RE: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?

Selected Duemilanove: same problem.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsyn...
mike5000
15:58 JeeLabs Café Support: Error uploading sketch to JeeNode V6. How to setup latest ver of Arduino IDE (v1.8.2) correctly?
I have a project where I will attempt to use the JeeNode V6 but I can't transfer the compiled sketch to the JeeNode:
...
mike5000
 

Also available in: Atom