Project

General

Profile

I don't get DIJN 9/10 to work

Added by physikus over 6 years ago

Hi,

I installed housemon on a raspi running Debian as written in the DIJN series. A Jeelink is plugged into the raspi. One jeenode sends a single byte every 15 seconds. On the console everything is fine:
@
pi@jeehome /housemon\ \$\ cat\ </dev/ttyUSB0

[RF12demo.8] Z i26 g212 @ 868 MHz
DF I 737 17

Available commands:
\ i\ -\ set\ node\ ID\ (standard\ node\ ids\ are\ 1..26)
\ (or\ enter\ an\ uppercase\ ’A’..’Z’\ to\ set\ id)
\ \ b\ -\ set\ MHz\ band\ (4\ =\ 433,\ 8\ =\ 868,\ 9\ =\ 915)
\ \ g\ -\ set\ network\ group\ (RFM12\ only\ allows\ 212,\ 0\ =\ any)
\ \ c\ -\ set\ collect\ mode\ (advanced,\ normally\ 0)
\ t\ -\ broadcast\ max-size\ test\ packet,\ with\ ack
\ …,\ a\ -\ send\ data\ packet\ to\ node\ ,\ with\ ack
\ …,\ s\ -\ send\ data\ packet\ to\ node\ ,\ no\ ack
\ \ l\ -\ turn\ activity\ LED\ on\ PB1\ on\ or\ off
\ \ q\ -\ set\ quiet\ mode\ (1\ =\ don’t\ report\ bad\ packets)
Remote\ control\ commands:
\ ,,,\ f\ -\ FS20\ command\ (868\ MHz)
\ ,,\ k\ -\ KAKU\ command\ (433\ MHz)
Flash\ storage\ (JeeLink\ only):
\ d\ -\ dump\ all\ log\ markers
\ ,,,,,\ r\ -\ replay\ from\ specified\ marker
\ 123,,\ e\ -\ erase\ 4K\ block
\ 12,34\ w\ -\ wipe\ entire\ flash\ memory
Current\ configuration:
\ Z\ i26\ g212\ @\ 868\ MHz
OK\ 1\ 25
OK\ 1\ 25
@
However,\ when\ I\ start\ npm\ and\ go\ to\ the\ demo\ page,\ I\ cannot\ see\ any\ value\ :-(
npm\ prints\ the\ following\ to\ the\ console:
@
pi@jeehome/housemon \$ npm start
npm WARN package.json housemon@0.6.0 No repository field.

> housemon@0.6.0 start /home/pi/housemon
> node app.js

pid 4561 Sat Jul 20 2013 19:09:06 GMT+0200 (CEST)
Starting SocketStream 0.3.4 in development mode…
briqs loaded
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
➙ event:all ss-store
install briq rf12demo:ttyUSB0
➙ event:all ss-store
install briq demo
➙ event:all ss-store
✎ CSS files changed. Updating browser…
✎ Client files changed. Reloading browser…
➙ event:all ss-tick
➙ event:all ss-tick
➙ event:all ss-tick
➙ event:all ss-tick
@
Have I forgotten anything? I don’t think so. But according to the DIJN series I should get a value on the demo page. But there is nothing. I did a git pull earlier this day on housemon. Likewise the system is up to date. Could someone tell me where I can start to dig to get back on the road to success?

Regards,

Physikus.


Replies (1)

RE: I don't get DIJN 9/10 to work - Added by physikus over 6 years ago

Ah, I found my mistake: I did not change the group ID to 100. Now, instead I modified briqs/demo.coffee as in http://jeelabs.net/boards/9/topics/1792.
Now it works.
Physikus.

    (1-1/1)